3D scan of O2 cdrom front panel.

For discussion of triage and repairs to SGIs as well as general hardware questions
Post Reply
User avatar
kikems
Posts: 78
Joined: Sun May 13, 2018 1:35 pm

3D scan of O2 cdrom front panel.

Post by kikems » Thu Aug 09, 2018 8:20 am

Hi friends, I'd make a 3D scan of my O2 front bezel. Now I need someone that help me to make a reverse enginering or remodel an idealized 3D model for make it available for download for other users can make their own 3D print replacement.
O2CDfrontpanel3Dscan.JPG
:O2: O2 R12k :Crimson: Iris Crimson Elan R4400 :Octane: Octane R10k

User avatar
CB_HK
Posts: 32
Joined: Sat May 26, 2018 2:03 am

Re: 3D scan of O2 cdrom front panel.

Post by CB_HK » Fri Aug 10, 2018 10:15 am

Kikems, I'll be happy to try working on it. Can't make any promises, but 3D printing is one of my hobbies and I'd love to help out the community with some parts that can be printed to replace things that are hard to get or impossible at this point.
:Indigo2: R10K | Solid IMPACT
:Indigo: R3K | Entry Graphics (LG2)
:Crimson: R4K | Elan Graphics

User avatar
kikems
Posts: 78
Joined: Sun May 13, 2018 1:35 pm

Re: 3D scan of O2 cdrom front panel.

Post by kikems » Thu Aug 16, 2018 6:50 pm

Here the model scanned, need remodel but have the real sizes.
o2_frontCD.zip
3dscanO2part.png
:O2: O2 R12k :Crimson: Iris Crimson Elan R4400 :Octane: Octane R10k

User avatar
CB_HK
Posts: 32
Joined: Sat May 26, 2018 2:03 am

Re: 3D scan of O2 cdrom front panel.

Post by CB_HK » Fri Aug 17, 2018 1:18 pm

I’ll start tinkering with it!

As an aside, since I don’t have an O2, I’m guessing the button in the bottom right corner is meant to be moveable. If that’s the case I need to know so that I don’t model it altogether as one piece. That would make it less than useful. Hah!
:Indigo2: R10K | Solid IMPACT
:Indigo: R3K | Entry Graphics (LG2)
:Crimson: R4K | Elan Graphics

JacquesT
Posts: 124
Joined: Mon May 21, 2018 2:06 pm
Location: Somerset, UK

Re: 3D scan of O2 cdrom front panel.

Post by JacquesT » Fri Aug 17, 2018 2:29 pm

Yes it is, it's mounted on a plastic support internally and is used to engage the CDROM eject microswitch.
:Octaneb: 1x 400Mhz R12k, 1Gb, V8, 6.5.30
:O2: 300Mhz R5200, 384Mb, 6.5.22m, FPA with :1600SW: [300Mhz R12k project in the works]

User avatar
CB_HK
Posts: 32
Joined: Sat May 26, 2018 2:03 am

Re: 3D scan of O2 cdrom front panel.

Post by CB_HK » Fri Aug 17, 2018 2:43 pm

JacquesT wrote:
Fri Aug 17, 2018 2:29 pm
Yes it is, it's mounted on a plastic support internally and is used to engage the CDROM eject microswitch.
I thought as much. Thank you for clarifying!
:Indigo2: R10K | Solid IMPACT
:Indigo: R3K | Entry Graphics (LG2)
:Crimson: R4K | Elan Graphics

JacquesT
Posts: 124
Joined: Mon May 21, 2018 2:06 pm
Location: Somerset, UK

Re: 3D scan of O2 cdrom front panel.

Post by JacquesT » Fri Aug 17, 2018 3:10 pm

You'll see my side retention clips are broken, it's held in place with what goes for 'blue tack' here in the UK (aka Prestik)

Image
:Octaneb: 1x 400Mhz R12k, 1Gb, V8, 6.5.30
:O2: 300Mhz R5200, 384Mb, 6.5.22m, FPA with :1600SW: [300Mhz R12k project in the works]

Post Reply