Your hinv's (Post them here:)
#31
RE: Your hinv's (Post them here:)
(10-07-2018, 03:00 PM)bjornl Wrote:  I think the hinv is unecessary long. Because there are different types of cpus in the system the list each cpu as a separate line.

It's a great testament to SGI's engineering that different CPU speeds and cache sizes can be mixed in one multi-processor system.  Some other architectures won't allow that.  Heck, it's impressive just to see so many CPUs in a single system (rather than a cluster).  I love seeing all the SCSI channels and Ethernet interfaces enumerated, too.  What would be the point of lots CPUs without impressive I/O to interface to them?

Great system. Thanks for posting that!

SGI:  Indigo, Indigo2, Octane, Origin 300
Sun:  SPARCstation 20 (x3), Ultra 2, Blade 2500, T5240
HP:  9000/380, 425e, C8000
Digital: DECstation 5000/125, PWS 600au
jpstewart
Octane

Posts: 79
Threads: 0
Joined: May 2018
Find Reply
10-07-2018, 03:27 PM
#32
RE: Your hinv's (Post them here:)
Code:
OCTODAD 2# hinv
4 800 MHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 2.2
FPU: MIPS R16010 Floating Point Chip Revision: 2.2
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3/IOC4 serial port: tty5
IOC3/IOC4 serial port: tty6
Graphics board: SG2
Graphics board: SG2
Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
Iris Audio Processor: version EMU revision A4, number 1
IOC3/IOC4 external interrupts: 1
USB controller: type OHCI
USB Human Interface Device: device id 0 type keyboard
USB controller: type OHCI


It's getting there!

Obligatory upskirt shot as well.

[Image: vAthiLD.jpg]

Indy Indigo2 Indigo2 IMPACT Indigo2 IMPACT Indigo2 IMPACT Indigo Indigo Octane Octane Octane Octane Octane2 Two O350 IRIS Crimson
CiaoTime
Maple Syrup Enthusiast

Posts: 34
Threads: 4
Joined: Jul 2018
Find Reply
10-27-2018, 01:51 AM
#33
RE: Your hinv's (Post them here:)
(10-07-2018, 03:00 PM)bjornl Wrote:  Here's my Origin 2000 with 64 cpus, which I think is maximum cpu count without special router.

<snip>
What software can I run to stresstest this Smile?

holy cow!  now that is an impressive setup!  Honestly good question though, I can think of many things to do with a 64cpu sgi, but without graphics I dunno - only thing I can think of is a compiling/dev system.  I've heard of people using an o2 or octane to "front-end" to a big origin system, but I never really had any understand what they could possibly be doing other than running something like a compiler or number crunching program (factoring primes, etc)

edit: btw we could really use a seperate "hinv/show off your stuff" category Smile
(This post was last modified: 10-27-2018, 03:08 AM by gijoe77.)
gijoe77
Tezro

Posts: 601
Threads: 33
Joined: Jun 2018
Find Reply
10-27-2018, 03:08 AM
#34
RE: Your hinv's (Post them here:)
(07-13-2018, 09:07 PM)jan-jaap Wrote:  <QUOTE author="Irinikus" post_id="1402" time="1531046292" user_id="62">
Irinikus Wrote:Very nice clean machine, now all you need is that Elan door to complete her! (if you can get your hands on the correct font, you could always get the Elan logo silkscreened onto your machines's existing door.)
Not necessarily ... the "Elan silkscreen door" goes with an R3000 Elan Indigo. The R4x00 Elan Indigo had a standard (blank?) door and an "Elan" badge.

The devil is in the details Smile

When I got my Indigo decades ago, it was a R3000 XZ but it had the Elan door for some reason. It didn't have the badge, so when I upgraded it to the R4400/150mhz I got the Elan badge and kept the Elan door, I think it just looks more complete that way 👍

[Image: XbXG0sz.jpg]

[Image: mnTvJeq.png]
(This post was last modified: 10-27-2018, 03:57 AM by BackPlaner.)
BackPlaner
Jurassic Technologist

Posts: 179
Threads: 26
Joined: Sep 2018
Find Reply
10-27-2018, 03:56 AM
#35
RE: Your hinv's (Post them here:)
I upgraded my Onyx2 to Infinite Reality 4 Smile

I think the deskside Onyx2 is one of the best systems to have: you can play with Infinite Reality without having to deal with the space, noise and power requirements of a tall rack.

This is about as far as you can take the Onyx2: R14K CPUs, 8GB RAM, IR4 with dual RM11's. It's got FC, dual gigabit ethernet, and a full set of DMediaPro HD video I/O hardware: a DM2 board, a DG5-TVO with a pair of DVI ports for HD-GVO applications using an external DMediaPro VBOB (with a DM5, the same vbob as used by the Octane2/Tezro).

I intend to run Discreet Inferno on it.

hinv

Code:
lego 1# hinv -mv
Location: /hw/module/1/slot/n2/node
           IP31 Board: barcode KRN340     part 030-1523-001 rev  C
   IP31PIMMR14K Board: barcode MJJ973     part 030-1547-002 rev  E
Location: /hw/module/1/slot/n1/node
       MODULEID Board: barcode K0027878   part              rev  
   IP31PIMMR14K Board: barcode MJW458     part 030-1547-002 rev  E
           IP31 Board: barcode MHZ719     part 030-1523-001 rev  C
     4P1G5_MPLN Board: barcode KVJ884     part 030-1066-002 rev  L
Location: /hw/module/1/slot/io4/kona
         GE16-4 Board: barcode LZM160     part 030-1398-001 rev  E
Location: /hw/module/1/slot/io6/xtalk_pci
      XTALK_PCI Board: barcode MMB502     part 030-1275-004 rev  A
Location: /hw/module/1/slot/io1/baseio
         BASEIO Board: barcode KWA975     part 030-0734-003 rev  A
            MIO Board: barcode KWG679     part 030-0880-003 rev  G
Location: /hw/module/1/slot/io5/xtalk_pci
      XTALK_PCI Board: barcode MFM649     part 030-1275-004 rev  A
Location: /hw/module/1/slot/io3/xt_digvid
      XT-DIGVID Board: barcode MGY958     part 030-1653-002 rev  G
4 500 MHZ IP27 Processors
CPU: MIPS R14000 Processor Chip Revision: 1.4
FPU: MIPS R14010 Floating Point Chip Revision: 1.4
CPU 0 at Module 1/Slot 2/Slice A: 500 Mhz MIPS R14000 Processor Chip (enabled)
 Processor revision: 1.4. Scache: Size 8 MB Speed 250 Mhz  Tap 0xa
CPU 1 at Module 1/Slot 2/Slice B: 500 Mhz MIPS R14000 Processor Chip (enabled)
 Processor revision: 1.4. Scache: Size 8 MB Speed 250 Mhz  Tap 0xa
CPU 2 at Module 1/Slot 1/Slice A: 500 Mhz MIPS R14000 Processor Chip (enabled)
 Processor revision: 1.4. Scache: Size 8 MB Speed 250 Mhz  Tap 0xa
CPU 3 at Module 1/Slot 1/Slice B: 500 Mhz MIPS R14000 Processor Chip (enabled)
 Processor revision: 1.4. Scache: Size 8 MB Speed 250 Mhz  Tap 0xa
Main memory size: 8192 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 1/Slot 82: 4096 MB (enabled)
 Bank 0 contains 512 MB (Standard) DIMMS (enabled)
 Bank 1 contains 512 MB (Standard) DIMMS (enabled)
 Bank 2 contains 512 MB (Standard) DIMMS (enabled)
 Bank 3 contains 512 MB (Standard) DIMMS (enabled)
 Bank 4 contains 512 MB (Standard) DIMMS (enabled)
 Bank 5 contains 512 MB (Standard) DIMMS (enabled)
 Bank 6 contains 512 MB (Standard) DIMMS (enabled)
 Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 81: 4096 MB (enabled)
 Bank 0 contains 512 MB (Standard) DIMMS (enabled)
 Bank 1 contains 512 MB (Standard) DIMMS (enabled)
 Bank 2 contains 512 MB (Standard) DIMMS (enabled)
 Bank 3 contains 512 MB (Standard) DIMMS (enabled)
 Bank 4 contains 512 MB (Standard) DIMMS (enabled)
 Bank 5 contains 512 MB (Standard) DIMMS (enabled)
 Bank 6 contains 512 MB (Standard) DIMMS (enabled)
 Bank 7 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
 Disk drive: unit 1 on SCSI controller 0 (unit 1)
 CDROM: unit 7 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3 parallel port: plp1
Graphics board: InfiniteReality4
Gigabit Ethernet: tg1, module 1, XIO slot io5 port 0
Gigabit Ethernet: tg2, module 1, XIO slot io5 port 1
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Iris Audio Processor: version RAD revision 7.0, number 1
Origin BASEIO board, module 1 slot 1: Revision 4
 PCI Adapter ID (vendor 0x1077, device 0x2312) PCI slot 1
 PCI Adapter ID (vendor 0x1077, device 0x2312) PCI slot 1
 PCI Adapter ID (vendor 0x14e4, device 0x1648) PCI slot 1
 PCI Adapter ID (vendor 0x14e4, device 0x1648) PCI slot 1
 PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
 PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
 PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
 PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
 PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
XT-DIGVID Multi-standard Digital Video: controller 0, unit 0, version 0x0
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 2: Revision 6 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 1: Revision 6 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n1: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io2: Revision 6.156

gfxinfo
Code:
lego 2# /usr/gfx/gfxinfo -v
Graphics board 0 is "KONAL" graphics.
       Managed (":0.0") 1920x1200
       Display has 2 channels
       4 GEs (of 4), occmask = 0x0f
       4MB external BEF ram, 32bit path
       2 RM11 boards (of 2) 1/1/0/0
       Texture Memory: 1024MB/1024MB/-/-
       Extra-Large pixel depth
       32K cmap
       TVO option detected
       brd: 80f61806 3061c06/3061c04/-/- f9191002
        ge: 0 14832057 24731057 14231057
       rm0: 05032057 35431057
             4631057 3/3/3/3
             4d31057 3/3/3/3/3/3/3/3
             4938057 5/5/5/5/5/5/5/5/5/5
       rm1: 05032057 35431057
             4631057 3/3/3/3
             4d31057 3/3/3/3/3/3/3/3
             4938057 5/5/5/5/5/5/5/5/5/5
        dg: 05532057
             5838057 1/1/1/1
             5631057 1/1
       GE:   NIC #:      0000.0052.2989 (family: 0b)
             Serial #:   LZM160
             Part #:     030-1398-001
       KT:   No NIC serial number available.
       RM0:  NIC #:      0000.006b.c9d4 (family: 0b)
             Serial #:   MRK516
             Part #:     030-1651-004
       TM0:  NIC #:      0000.006b.e2c4 (family: 0b)
             Serial #:   MNZ477
             Part #:     030-1650-003
       RM1:  NIC #:      0000.006c.60b7 (family: 0b)
             Serial #:   MTJ639
             Part #:     030-1651-004
       TM1:  NIC #:      0000.006c.5d89 (family: 0b)
             Serial #:   MTJ779
             Part #:     030-1650-004
       RM2:  No NIC serial number available.
       TM2:  No NIC serial number available.
       RM3:  No NIC serial number available.
       TM3:  No NIC serial number available.
       BP:   No NIC serial number available.
       DG:   NIC #:      0000.0083.6fe7 (family: 0b)
             Serial #:   NGS389
             Part #:     030-1242-001
       DGOPT:NIC #:      0000.0083.cae1 (family: 0b)
             Serial #:   NFW909
             Part #:     030-1511-004
       Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
       Channel 0:
        Origin = (0,0)
        Video Output: 1920 pixels, 1200 lines, 66.00Hz (1920x1200_66.vfo)
        Video Format Flags:  (none)
        Sync Output(s):
         Composite sync on Green
         Composite TTL sync on Aux 0
        Using Gamma Map
(This post was last modified: 02-06-2019, 10:09 PM by jan-jaap.)
jan-jaap
SGI Collector

Posts: 302
Threads: 11
Joined: Jun 2018
Website Find Reply
02-06-2019, 10:07 PM
#36
RE: Your hinv's (Post them here:)
Very nice! Big Grin

So how does it perform, compared to the IR3 system?

[Image: TNWhJMc.png]
(This post was last modified: 02-07-2019, 06:30 AM by Irinikus.)
Irinikus
Connoisseur

Posts: 926
Threads: 159
Joined: Dec 2017
Website Find Reply
02-07-2019, 06:05 AM
#37
RE: Your hinv's (Post them here:)
(02-07-2019, 06:05 AM)Irinikus Wrote:  So how does it perform, compared to the IR3 system?

Well, all I did so far is run 'irsaudit' to make sure it's 100% OK. I'm busy with the network here so the system isn't even wired at the moment. I did receive more parts (GE16-4's, RM11's etc) so I'll be busy for a while. I also have some new Gefen VGA to DVI Scalers (EXT-VGA-2-DVISP) and I want to see if that results in usable DVI output from the Onyx2. I will also have another look at the IR demos scripts vs. IR3/IR4.

IR4 should give a little extra compared to the jump from IR2E to IR3. In that case the performance is identical (I think), you just get a different texture memory board with 256MB instead of 64MB of TRAM. The frame buffer memory board of the sandwich is the same between RM9 and RM10. Not so for the RM11; you get a different raster board with 2.5GB of raster memory and the texture board has 1GB TRAM. It also has a higher fill rate. Other limitations of IR stay: you do not get more geometry performance, and you still cannot have two screens at 1920x1200.

So it's really going to depend on what you want to do with it. Discreet software makes good use of it, the number of HD streams you can handle simultaneously depends on the amount of TRAM. Of course the IR4 crushes the V12 there. Since I have the DM2 and the DG5-TVO I have what it takes to piece together a sweet Inferno setup. Originally, these ran on the tall rack Onyx2 which has many more XIO slots, so I don't know if I can install enough FC bandwidth in a deskside. Also, the 500MHz R14K CPUs are going to loose to the 1GHz R16Ks in the Tezro. Will be interesting to see where this goes.

I said it before: when it comes to the graphics of Silicon Graphics, the Onyx2 is the sweet spot. And IR4 is the ultimate graphics upgrade for the ultimate (silicon) graphics system you can still run in a residential setting. It's a taste of Infinite Reality without having to worry about 3-phase power and structural reinforcements to your house. I've seen a real life Onyx 3900 in action at a customer in ~ 2011. 7 tall racks, 7 IR4 pipes and "as many 1GHz CPUs as SGI was able to supply". It only makes me appreciate my little Onyx2 deskside more, because in the basis it's the same. The Onyx 3900 is just more of the same. Lots and lots more.
jan-jaap
SGI Collector

Posts: 302
Threads: 11
Joined: Jun 2018
Website Find Reply
02-07-2019, 08:41 AM
#38
RE: Your hinv's (Post them here:)
Will post here when not spam-blocked - Fuel and I2
Fuel details in another post.

For the I2 hinv, please see http://archive.irix.cc/apocrypha/nekonomicon.html
[url=http://archive.irix.cc/apocrypha/nekonomicon.html][/url]
(This post was last modified: 03-30-2019, 11:52 AM by ajw99uk.)
ajw99uk
Ex-SGI owner

Posts: 12
Threads: 1
Joined: Mar 2019
Find Reply
03-23-2019, 05:34 PM
#39
RE: Your hinv's (Post them here:)
Fuel


Code:
Location: /hw/module/001c01/node
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
Location: /hw/module/001c01/node/cpubus/0
        IP34PIMM Board: barcode MSY420     part 030-1891-001 rev -D
Location: /hw/module/001c01/Ibrick/xtalk/13
      ODY128B1_2 Board: barcode NWM092     part 030-1884-005 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/14
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
Location: /hw/module/001c01/Ibrick/xtalk/15
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
1 700 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 6: Version IEEE1394 SBP2
Integral SCSI controller 7: Version LS1030, low voltage differential
Integral SCSI controller 8: Version LS1030, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
  CDROM: unit 4 on SCSI controller 1
  Disk drive / removable media: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
  PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 1
  PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
  PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
  PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 2
  PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
  PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB controller: type OHCI
USB controller: type OHCI
ajw99uk
Ex-SGI owner

Posts: 12
Threads: 1
Joined: Mar 2019
Find Reply
03-23-2019, 06:52 PM


Forum Jump:


Users browsing this thread: 1 Guest(s)