AUTODESK FLAME 2008 SERVICE PACK 6
#1
AUTODESK FLAME 2008 SERVICE PACK 6
I have finally managed to license my flame 2008 package thanks to gijoe77! Big Grin

I have copied the Swr_license file to /etc and I have a problem in that I cannot setup a stonefs on my secondary disk in my Tezro.

I think that it's a problem with how the disk is partitioned.

Any help with this would be much appreciated!


   

   

   

   

   

   

[Image: rZbyrYx.png]
Irinikus
Connoisseur

Posts: 559
Threads: 76
Joined: Dec 2017
Website Find Reply
08-11-2018, 04:07 PM
#2
Re: AUTODESK FLAME 2008 SERVICE PACK 6
Irinikus, make sure that string in swr file is ONE LONG string without breaks. As far as I remember there may be only one CR - at the end of this string.

PS: by the way - did you stop S&W before run sw_config?
bkd
Octane

Posts: 70
Threads: 7
Joined: Jul 2018
Find Reply
08-11-2018, 05:33 PM
#3
Re: AUTODESK FLAME 2008 SERVICE PACK 6
You need "stonewire2008_filesystem_networking_guide.pdf", page 27 and walk step by step. Which step this error related to?
bkd
Octane

Posts: 70
Threads: 7
Joined: Jul 2018
Find Reply
08-11-2018, 05:38 PM
#4
Re: AUTODESK FLAME 2008 SERVICE PACK 6
I think you did not stopped stone&wire service before setting volumes for framestore. If I remember correctly you need do it - then you are allowed to "save device information", after starting sw service again it auto mounts volumes within framestore. Also if I see correctly you have marked "keep" gadget insted of "create" in upper left part of sw_config window. You need to mark create gedget because I suppose you want to create new framestore. I'm not sure because I'm far from machines.
waldemar72
O2

Posts: 36
Threads: 1
Joined: Aug 2018
Find Reply
08-11-2018, 05:46 PM
#5
Re: AUTODESK FLAME 2008 SERVICE PACK 6
I'm sure swr string is correct, if not a green block marking disk 2 on controller 0 would be white with marking "unlicensed". So first stop sw (if i remember correctly stop_sw command in sw directory), then sw_config (remember - create), then start_sw. That's the magic.
waldemar72
O2

Posts: 36
Threads: 1
Joined: Aug 2018
Find Reply
08-11-2018, 05:53 PM
#6
Re: AUTODESK FLAME 2008 SERVICE PACK 6
You said your problem is related to way your drive was partitioned. No, sw_config auto starts fx command and formats drive as needed.
waldemar72
O2

Posts: 36
Threads: 1
Joined: Aug 2018
Find Reply
08-11-2018, 05:57 PM
#7
Re: AUTODESK FLAME 2008 SERVICE PACK 6
You're right that I didn't stop the stonewire. (I didn't think it was necessary, as the system hadn't been setup before.)

I will fire up my Tezro and give it a try.

[Image: rZbyrYx.png]
Irinikus
Connoisseur

Posts: 559
Threads: 76
Joined: Dec 2017
Website Find Reply
08-11-2018, 06:25 PM
#8
Re: AUTODESK FLAME 2008 SERVICE PACK 6
I followed the instructions, and this is what I got:


   


Any ideas?

[Image: rZbyrYx.png]
Irinikus
Connoisseur

Posts: 559
Threads: 76
Joined: Dec 2017
Website Find Reply
08-11-2018, 06:44 PM
#9
Re: AUTODESK FLAME 2008 SERVICE PACK 6
Are you sure your drive is ok?
You could also try again with sw stopped, then in sw_config first clear or clear all, then again add+create. I had that issue as well but now I don't remember exactly what I did. I'll try tomorrow when I'll come back home.
Also reformating the drive in fx would be a good idea.
waldemar72
O2

Posts: 36
Threads: 1
Joined: Aug 2018
Find Reply
08-11-2018, 07:27 PM
#10
Re: AUTODESK FLAME 2008 SERVICE PACK 6
waldemar72 post_id=2238 time=1534015633 user_id=301 Wrote:Are you sure your drive is ok?
You could also try again with sw stopped, then in sw_config first clear or clear all, then again add+create. I had that issue as well but now I don't remember exactly what I did. I'll try tomorrow when I'll come back home.
Also reformating the drive in fx would be a good idea.

What type of drive should it be partitioned as? (root, option...?)

What type of file system? (xfs or efs?)

[Image: rZbyrYx.png]
Irinikus
Connoisseur

Posts: 559
Threads: 76
Joined: Dec 2017
Website Find Reply
08-11-2018, 07:35 PM


Forum Jump:


Users browsing this thread: 3 Guest(s)